Myślisz, że wymiatasz jeśli chodzi o NBA? Sprawdź się z innymi pasjonatami koszykówki. Odwiedź NBA QUIZ i wykaż się wiedzą!

Ocena wątku:
  • 0 Głosów - 0 Średnio
  • 1
  • 2
  • 3
  • 4
  • 5
Selection of grinding wheel in stone grinding
09-01-2019, 08:00
Post: #1
Selection of grinding wheel in stone grinding
Grinding is a method of cutting a workpiece with a grinding wheel as a cutting tool on a grinding machine. The characteristics of this method are:
(1) Since the grinding wheel itself has high hardness and heat resistance, the grinding can process materials with high hardness, such as hardened steel and hard alloy.
(2) The characteristics of the fiber cutting disc Chinese supplier and the grinding machine determine that the grinding process system can make uniform micro-cutting, generally ap=0.001~0.005mm; the grinding speed is very high, generally up to v=30~50m/s; the grinding machine has good rigidity; Hydraulic drive, so grinding can economically achieve high machining accuracy (it6 ~ it5) and small surface roughness (ra = 0.8 ~ 0.2μm). Grinding is one of the main methods of finishing parts.
(3) The temperature in the grinding zone is high due to severe friction. This can cause stress and deformation of the workpiece and even burn the surface of the workpiece. Therefore, a large amount of coolant must be injected during grinding to reduce the grinding temperature. The coolant can also act as chipping and lubrication.
(4) The radial force during grinding is large. This causes the elastic retraction of the machine tool-grinding wheel-workpiece system so that the actual depth of cut is less than the nominal depth of cut. Therefore, when the grinding is about to be completed, the knife should not be used for light grinding to eliminate the error.
(5) After the abrasive grain is blunt, the hot sale cutting wheel also increases, causing the abrasive grain to break or fall off, and the sharp edge is re-exposed. This characteristic is called “self-sharpness”. Self-sharpening enables grinding to work normally in a certain period of time, but after a certain working time, manual finishing should be carried out to avoid vibration, noise and damage to the surface quality of the workpiece.
Znajdź wszystkie posty użytkownika
Odpowiedz cytując ten post

Podobne wątki
Wątek: Autor Odpowiedzi: Wyświetleń: Ostatni post
  Wheel characteristics xzbbvfvbh 0 40 Wczoraj 05:00
Ostatni post: xzbbvfvbh
  Balance problem to be paid attention to when installing the grinding wheel xzbbvfvbh 0 101 17-01-2019 04:45
Ostatni post: xzbbvfvbh
  Resin grinding wheel cleaning method and installation xzbbvfvbh 0 183 05-01-2019 07:31
Ostatni post: xzbbvfvbh
  How To Transport Fast Working Grinding Wheel? juniperqq 0 235 28-12-2018 08:28
Ostatni post: juniperqq
  What are the classifications of grinding tools? xzbbvfvbh 0 217 26-12-2018 09:01
Ostatni post: xzbbvfvbh
  Difference between cutting piece and grinding wheel xzbbvfvbh 0 146 18-12-2018 07:49
Ostatni post: xzbbvfvbh
  thin flat cutting disc grinding xzbbvfvbh 0 140 15-12-2018 08:28
Ostatni post: xzbbvfvbh
  Grinding efficiency of grinding wheel knowledge xzbbvfvbh 0 194 06-12-2018 07:50
Ostatni post: xzbbvfvbh
  Types and characteristics of grinding wheels xzbbvfvbh 0 190 04-12-2018 08:06
Ostatni post: xzbbvfvbh
  Factors affecting the surface roughness of grinding machine and its improvement measu xzbbvfvbh 0 208 16-11-2018 10:12
Ostatni post: xzbbvfvbh

Skocz do:

Użytkownicy przeglądający ten wątek: 1 gości