Myślisz, że wymiatasz jeśli chodzi o NBA? Sprawdź się z innymi pasjonatami koszykówki. Odwiedź NBA QUIZ i wykaż się wiedzą!

Ocena wątku:
  • 0 Głosów - 0 Średnio
  • 1
  • 2
  • 3
  • 4
  • 5
How to reduce the grinding pressure
14-10-2017, 04:06
Post: #1
How to reduce the grinding pressure
SBM is committed to the powder products industry, ultrafine mill machinery and equipment more than ten years as a day of innovation and real development. In the market there are many loyal customers and considerable sales. High-quality ultrafine mill to the customer to bring high efficiency, high yield, high yield of production, is the choice of many processing enterprises of ore.
ultrafine mill in the production, large pieces of material by the jaw crusher to the required size of about 1cm after the material from the hopper to the hopper, and then by the electromagnetic vibration feeder to the material evenly and continuously sent Into the host grinding room for grinding. After the grinding of the material by the fan air into the separator for grading, in the separator under the action of the impeller, does not meet the fineness of the material falling into the grinding room to re-milling, fineness of the material requirements with the air through the pipeline Into the cyclone collector, the separation of the collection, the discharge device is discharged as finished powder.
If the material to be ground contains a certain amount of water, grinding will produce heat, grinding chamber gas evaporation and expansion of the system to change the amount of gas flow, coupled with the inlet and the junction of the pipe seal, the outside air Of the entry into the system to make the air flow out of balance, for which ultrafine mill through the fan outlet in the exhaust pipe valve, the excess gas into the bag filter, and after purification, in the regulation of system airflow balance While achieving environmentally friendly production.
On the grinding roller, grinding ring and other wearing parts of the processing, SBM using high-quality materials and design principles. In the work of ultrafine mill of the roller and the disc does not touch, wear less, long service life. Roller can be turned out to the chassis outside the repair, replace the roller sleeve, liner convenient and reduce downtime. Roller lubrication with a separate lubrication station, and a single roller circuit using dual pump - pump suction at the same time work mode, even if the roller bearing is fully lubricated and cooling, but also to avoid roller bearing indoor oil too much leakage.
So the material processing equipment, you still hesitate what? The value of ultrafine mill is not just the above content. When you choose the right equipment, SBM tailor-made for your quality production program, ultrafine mill will shine.
Znajdź wszystkie posty użytkownika
Odpowiedz cytując ten post

Podobne wątki
Wątek: Autor Odpowiedzi: Wyświetleń: Ostatni post
  Grinding burns and their solutions xzbbvfvbh 0 18 03-12-2018 06:35
Ostatni post: xzbbvfvbh
  Analysis of cheap grinding disc juniperqq 0 25 29-11-2018 08:23
Ostatni post: juniperqq
  How to solve the grinding vibration pattern? xzbbvfvbh 0 22 29-11-2018 07:13
Ostatni post: xzbbvfvbh
  Common problems and solutions for grinding without center grinding xzbbvfvbh 0 25 28-11-2018 07:40
Ostatni post: xzbbvfvbh
  Grinding machine safety operation procedures xzbbvfvbh 0 19 27-11-2018 08:11
Ostatni post: xzbbvfvbh
  Solution for failure of ultra-fine grinding components xuanxuankuaile 0 27 13-11-2018 06:45
Ostatni post: xuanxuankuaile
  Four methods to reduce dust pollution from crushers xuanxuankuaile 0 22 05-11-2018 09:37
Ostatni post: xuanxuankuaile
  What are the precautions for micro-powder grinding during operation? xuanxuankuaile 0 35 02-11-2018 06:55
Ostatni post: xuanxuankuaile
  How should the ultra-fine grinding bearing be maintained? xuanxuankuaile 0 25 01-11-2018 04:19
Ostatni post: xuanxuankuaile
  How to effectively reduce the sudden accident of the cone crusher xuanxuankuaile 0 31 11-10-2018 04:49
Ostatni post: xuanxuankuaile

Skocz do:

Użytkownicy przeglądający ten wątek: 1 gości