Myślisz, że wymiatasz jeśli chodzi o NBA? Sprawdź się z innymi pasjonatami koszykówki. Odwiedź NBA QUIZ i wykaż się wiedzą!

Odpowiedz 
 
Ocena wątku:
  • 1 Głosów - 5 Średnio
  • 1
  • 2
  • 3
  • 4
  • 5
Grinding disc grinding factor
01-11-2018, 08:16
Post: #1
Grinding disc grinding factor
  The depressed grinding disc in stock base has large deformation, inconsistent thickness and large tolerance of the inner hole. When there is a problem with the congenital defects of the above-mentioned substrate, there is a grinding error regardless of the type of equipment used. The deformation of the base body deviates from the two side angles; the thickness of the base body is inconsistent with respect to the back angle and the rake angle. If the cumulative tolerance is too large, the quality and accuracy of the saw blade are seriously affected.

  Welding factor. When welding, the alloy has a large deviation to the medium degree, which affects the grinding precision. When the grinding head is pressed, the pressure is small, the back angle also produces the above factors, the welding angle is poor, and the human inevitable factors are all related to the depressed grinding disc in stock during grinding. Factors have an unavoidable impact.

  The quality of the low price grinding disc and the influence of the width of the grinding disc. When using the grinding disc to grind the alloy sheet, pay attention to the particle size of the grinding disc, and the grain size is too coarse to grind to produce the grinding disc trace. The low price grinding disc is fine in size and easy to block the grinding amount and easy to burn the knife. The diameter of the grinding disc and the thickness of the depressed grinding disc in stock are determined according to the length and width of the alloy or the different tooth shapes and the various surfaces of the alloy. It is not a chamfer or front angle grinding disc. The grinding can be arbitrarily ground with different tooth shapes. Specification grinding disc.
 
  The grinding head feed rate, the choice of grinding disc size is extremely important for the amount of feed. General depressed grinding disc in stock is recommended to use 180# to 240# extreme quantity selection 240# to 280# not to use 280# to 320#, otherwise, the feed rate should be adjusted.

  Grinding center. All saw blades are centered on the base, not centered on the edge, the plane grinding center cannot be taken out, the back corner, the front corner cannot be used to grind a saw blade, and the saw blade is ground in three processes. The center cannot be ignored. When grinding the side angles, the thickness of the alloy is carefully observed. The thickness of the grinding center changes accordingly. Regardless of the thickness of the alloy, the center line of the depressed grinding disc in stock should be kept in line with the welding position when grinding the surface, otherwise, the angle difference will affect the cutting.
Znajdź wszystkie posty użytkownika
Odpowiedz cytując ten post
Odpowiedz 


Podobne wątki
Wątek: Autor Odpowiedzi: Wyświetleń: Ostatni post
  The difference between grinding wheel and shallow saw blade juniperqq 0 68 16-11-2018 10:48
Ostatni post: juniperqq
  Different before and after the grinding disc is used juniperqq 0 80 05-11-2018 08:48
Ostatni post: juniperqq
  What Is Grinding Wheel For Stainless Steel juniperqq 0 68 02-11-2018 08:52
Ostatni post: juniperqq
  Electroplated diamond long life grinding wheel advantages juniperqq 0 78 31-10-2018 08:30
Ostatni post: juniperqq
  Introduction to wear characteristics of grinding wheel juniperqq 0 58 29-10-2018 12:08
Ostatni post: juniperqq
  What is the cause of the blockage of the grinding wheel? juniperqq 0 84 25-10-2018 08:34
Ostatni post: juniperqq
  Process defects of traditional production of grinding wheels juniperqq 0 90 24-10-2018 08:32
Ostatni post: juniperqq
  Reasons and solutions for the breakdown of grinding wheels (Part Two) juniperqq 0 90 23-10-2018 10:24
Ostatni post: juniperqq
  Abrasives of grinding wheels juniperqq 0 79 22-10-2018 10:04
Ostatni post: juniperqq
  Characteristics of grinding juniperqq 0 68 18-10-2018 10:25
Ostatni post: juniperqq

Skocz do:


Użytkownicy przeglądający ten wątek: 1 gości